- Swap instead of wait The station lifts a depleted pack out of a mobile robot and fits a charged one, so the robot leaves with a full battery rather than standing on a charger.
- Replacement within 60 seconds That figure covers the exchange operation itself; recharging the removed pack happens afterwards in a slot while the robot is already back at work.
- Three charging slots The station holds three packs under automatic charging management, and the manufacturer notes that slot quantity can be changed, with total height following the slot count.
- Vision-guided magnet pickup A magnet-type mechanism with automatic detection picks the pack up, and one vision unit corrects its position within ±15 mm on X and Y to an accuracy of ±0.2 mm.
- CC/CV charging with a slow start Charging follows a constant current / constant voltage profile to a maximum of 29 V, with the current raised in four steps after the start for a slow start.
- Charge-level discharge management The station monitors packs by charge level and discharges them automatically, and supports power failure compensation when external power is supplied.
- Operator panel and alarms A touch panel and buttons run the station, one emergency stop is fitted, and a four-colour indicator with a warning sound shows status across the floor.
Description
The BCU is a battery exchange station, not a robot. It does not drive, carry anything or perform tasks of its own. A mobile robot comes to it, the station takes the depleted pack out and fits a charged one, and the robot goes back to work while the removed pack recharges in a slot. The manufacturer presents that as a way to keep a fleet running without charging pauses; how far it goes depends on fleet size, duty cycles and planning rather than on the station alone.
The exchange itself is specified at within 60 seconds. Pickup uses a magnet-type mechanism with automatic detection, helped by a single vision unit that finds the pack and corrects for misalignment within ±15 mm on both X and Y to an accuracy of ±0.2 mm — so a robot does not have to stop perfectly, only close enough. Local communication with autonomous mobile robots is RF PIO; anything beyond that interface is confirmed with the manufacturer.
Charging runs on a constant current / constant voltage profile to a maximum of 29 V, with a four-step current increase after the start that the manufacturer calls a slow start. The station also monitors packs by charge level and discharges them automatically, and it supports power failure compensation when external power is supplied. Operators work through a touch panel and buttons, with one emergency stop and a four-colour indicator plus warning sound.
Read the battery line carefully. The pack is Li-ion, rated 25 V 100 A; its amp-hour capacity is confirmed with the quotation, so the rating should not be converted into Ah, watt-hours or runtime. The 15 kg figure is the mass of the battery, not of the station. The three-slot unit measures 900 x 1,550 x 1,350 mm and needs a 220 VAC / 30 A supply, an ambient range of 0 to +40 degrees Celsius, and a floor free of water, oil and dirt.
Key Capabilities
- Swap instead of wait: The station lifts a depleted pack out of a mobile robot and fits a charged one, so the robot leaves with a full battery rather than standing on a charger.
- Replacement within 60 seconds: That figure covers the exchange operation itself; recharging the removed pack happens afterwards in a slot while the robot is already back at work.
- Three charging slots: The station holds three packs under automatic charging management, and the manufacturer notes that slot quantity can be changed, with total height following the slot count.
- Vision-guided magnet pickup: A magnet-type mechanism with automatic detection picks the pack up, and one vision unit corrects its position within ±15 mm on X and Y to an accuracy of ±0.2 mm.
- CC/CV charging with a slow start: Charging follows a constant current / constant voltage profile to a maximum of 29 V, with the current raised in four steps after the start for a slow start.
- Charge-level discharge management: The station monitors packs by charge level and discharges them automatically, and supports power failure compensation when external power is supplied.
- Operator panel and alarms: A touch panel and buttons run the station, one emergency stop is fitted, and a four-colour indicator with a warning sound shows status across the floor.
This model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.
Buying through Robotix Market
This unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.
Features
Specs
| Brand | Wonik Robotics |
|---|---|
| Manufacturer | Wonik Robotics, South Korea |
| Model | BCU |
| Product Type | Automatic battery replacement and charging station for mobile robots |
| Battery Replacement | Automatic, with power failure compensation (external power supplied) |
| Battery Replacement Speed | Within 60 seconds |
| Charging Slots | 3 (quantity can be changed) |
| Dimensions (W x L x H) | 900 x 1,550 x 1,350 mm (3 slots; total height depends on slot count) |
| Battery Type | Li-ion, 25V 100A (Ah capacity confirmed at quote) |
| Battery Weight | 15 kg (mass of the battery, not of the station) |
| Input Power | 220VAC / 30A |
| Charging Voltage | Max 29V |
| Charging Method | Constant current / constant voltage (CC/CV); 4-step current increase after start |
| Battery Discharge Management | Monitoring per charge level and automatic discharge |
| Battery Pickup Method | Magnet type with automatic detection and position correction |
| Position Correction Range | X: ±15 mm, Y: ±15 mm |
| Position Correction Accuracy | ±0.2 mm |
| Vision | 1 unit for battery pickup position detection and correction |
| Control Panel | Touch panel / button |
| Emergency Stop | 1 |
| Alarm | 4-colour indicator and warning sound |
| Ambient Operating Temperature | 0 to +40 °C |
| Floor Requirements | No water, no oil, no dirt |
| Local Communication (AMR) | RF PIO |
| Battery Capacity (Ah) | Confirm at quote |
| Station Weight | Confirm at quote |
| Charging Time per Pack | Confirm at quote |
| Compatible Robot Models | Confirm at quote |
Industries
Frequently Asked Questions
It is offered by quotation — configuration, quantity and delivery are confirmed per project.
No. It is a battery replacement and charging station that serves mobile robots which come to it. It does not drive, transport loads or manipulate objects, and it is specified as fixed infrastructure rather than a vehicle.
Within 60 seconds, and that covers the swap operation only. Recharging the pack that was removed happens afterwards in one of the charging slots while the robot is already operating again.
The pack is Li-ion, rated 25 V 100 A. That rating should not be read as 100 Ah or converted into watt-hours or runtime; the amp-hour capacity and energy figure are confirmed with the quotation.
Within the correction window. A magnet-type pickup with automatic detection, assisted by one vision unit, compensates for misalignment of up to ±15 mm on the X and Y axes, with a correction accuracy of ±0.2 mm.
A 220 VAC / 30 A supply, an ambient temperature between 0 and +40 degrees Celsius, and a floor free of water, oil and dirt. The three-slot unit occupies 900 x 1,550 x 1,350 mm, and total height changes with the number of slots specified.
Recently Viewed
You haven't viewed any products yet.
